An incident involving a crew member who sustained a finger injury while attempting to restrain a rotating belt during maintenance highlights the risks of residual mechanical energy even after electrical isolation.
In Safety Flash SF 20/26, published on 18 November 2026, the International Marine Contractors Association (IMCA) highlighted the importance of controlling residual mechanical energy and ensuring that equipment is safe before maintenance begins.
What happened
The incident occurred while a crew member was repairing a broken grease nipple on an Air Handling Unit (AHU).
Although the electrical supply had been isolated, the unit’s V-belt continued to rotate because residual mechanical energy remained in the system.
During the maintenance activity, the crew member attempted to restrain the moving belt manually. Two fingers were subsequently pulled into the pinch point formed between the belt and pulley.
The incident caused a laceration and a hairline fracture to a fingertip.
Following medical assessment, the injury was classified as a Restricted Work Case (RWC). The event as High Potential (HIPO), recognising that the consequences could have been significantly more serious, including the possible loss of one or more fingers.
The safety flash does not provide further information about the working arrangements, the duration of the maintenance activity or whether other personnel were present.
Nevertheless, the sequence of events identifies an important safety concern: isolating an electrical supply does not necessarily eliminate the mechanical energy that can cause equipment to move.
What went wrong
The immediate danger arose from contact with a rotating component that had not reached a verified safe condition.
Electrical isolation had been carried out, but the belt remained capable of movement. The worker’s attempt to restrain it manually placed his fingers directly within the hazardous area between two moving components.
The incident therefore demonstrates the difference between disconnecting equipment from its power supply and confirming that all relevant energy has been controlled.
The mechanical energy must be identified, verified and controlled by an authorised and competent person before maintenance begins.
The association also questioned whether generic risk assessments provide sufficient protection for tasks involving rotating machinery. A general assessment may identify the presence of moving components without adequately addressing the specific hazards associated with the equipment, maintenance activity and available isolation arrangements.
A particular risk assessment was completed or whether inadequate supervision contributed to this incident. These remain broader considerations raised by its recommendations rather than confirmed findings.
The big picture
The incident highlights a machinery-safety issue that extends beyond the particular maintenance task. Equipment that has been switched off can remain hazardous when mechanical movement continues or stored energy has not been adequately controlled.
A machinery demonstrated the severity of this risk. In that incident, a worker suffered life-changing hand injuries after touching the still-rotating blades of a portable blower whose electrical supply had been disconnected.
The need for effective controls has also been highlighted by the Liberia Maritime Authority’s guidance on preventing hand injuries, which identifies pinch points, inadequate hazard assessment and unsafe contact with machinery among recurring concerns.
These examples demonstrate why machinery isolation should be treated as a complete safety process rather than an individual action.
For ship operators, the wider consideration is whether maintenance procedures distinguish between isolating a power source and verifying that the equipment is no longer capable of hazardous movement.
This is particularly relevant to routine interventions, where the familiarity of the equipment or apparently limited scope of the work should not reduce the level of protection required.
What could have prevented the injury?
IMCA’s recommendations focus on ensuring effective energy isolation, preventing manual contact with rotating machinery and strengthening task-specific risk assessments.
The following practical considerations can support safer maintenance operations:
- Verify a zero-energy state: Electrical isolation should be followed by confirmation that residual mechanical energy has been controlled and that components have stopped moving before work begins.
- Keep hands away from moving components: Personnel must never attempt to slow, stop or restrain rotating equipment manually. Machinery should be allowed to stop completely or be secured using an approved method.
- Assess the specific task: Risk assessments should address the actual equipment, its potential energy sources, accessible pinch points and the safeguards required for the intended intervention.
- Review working arrangements: IMCA advises discouraging lone working during tasks involving energised machinery or equipment and avoiding it wherever practicable.
- Consider appropriate hand protection: Glove selection, including possible impact protection, should form part of the risk assessment. However, protective gloves must not be considered a substitute for controlling moving machinery.
These considerations also connect with established lockout/tagout guidance for handling energy sources onboard, which addresses the need to control hazardous energy during servicing, inspection and maintenance.
Ultimately, maintenance should only proceed once the equipment’s condition has been verified and the necessary safeguards are in place.
The incident raises several questions that Masters, engineers, supervisors and crew members can discuss during safety meetings and toolbox talks:
- How do we verify that rotating equipment is completely safe after electrical isolation?
- Which maintenance tasks involve the possibility of residual mechanical energy, and how are these risks addressed in our procedures?
- How do we prevent personnel from attempting to stop or adjust moving equipment manually?
- What arrangements ensure that maintenance is appropriately assessed and supervised, particularly when a crew member is working alone?
Key takeaways
- Electrical isolation is not the same as zero energy. Mechanical movement may continue after the power supply has been disconnected.
- Never manually restrain rotating equipment. Hands must remain clear of belts, pulleys and other moving components.
- Risk assessments must reflect the task. Generic precautions may not adequately address equipment-specific hazards.
- Working arrangements matter. Supervision and the risks associated with lone working should be considered before maintenance begins.
- Verify safety before intervention. Equipment should not be approached until its hazardous energy has been effectively controlled.